Log Max 3000T

CABEZALES

Ficha Técnica

Descargue la ficha técnica en formato PDF

Log Max 3000T es un cabezal procesador de nueva generación, empleado para operaciones con madera delgada, que se adapta mejor a las grúas de largo alcance. Este cabezal presenta una nueva geometría en su bastidor, que adelanta la parte superior del mismo para evitar que la rueda de medición se obstruya.

Accionado hidráulicamente por dos motores de pistones radiales de 398 cc (24.3 cu.in.) o 364 cc (22.2 cu.in.) ofrece cerca de dos toneladas de fuerza en tracción

El cabezal Log Max 3000T presenta la nueva unidad de sierra Log Max 218 o 318, (manual o con sistema de autotensión) también disponible en la versión True-Cut

Todas estas características combinadas con el sistema patentado de control de cuchillas Log Max, que minimiza la fricción de la alimentación, proporciona una excelente cobertura del fuste y una mayor calidad en la troza.

Harvesting key figures
  • Gama más productiva : 8 to 30 cm
  • Diámetro máximo de corte : 51,6 cm
  • Diámetro de desrame mínimo : 1,2 cm

carriers

12-16 toneladas

carriers

13-18 toneladas

carriers

100-120 kNm

DIMENSIONS & WEIGHT

  • Max width arms open 1129 mm
  • Min width with arms closed 964 mm
  • Height to felling link 1325 mm
  • Standard configuration (1) 623 kg

1) Incl: V-Steel rollers, rotator and damped protection plate

 

FELLING/CUTTING – SAW TYPE

Hydraulically driven chain saw with pressure controlled feed force.
Chain oil tank in frame with 4 liters capacity.

 

  • Saw type Saw 218 / 318
  • Saw motor 19 cc
  • Saw chain 0.404 pitch
  • Bar length, 60 cm
  • Maximum cut capacity std/opt 51,6 cm

Optional saw:

  • Saw type Saw 218 True-Cut / 318 True-Cut
  • Saw motor 19 cc
  • Saw chain 0.404 pitch
  • Bar length, std/opt60 cm
  • Maximum cut capacity, std/opt51,6 cm

FEEDING

Two hydraulically driven rollers mounted directly on radial piston motors, 398 cc / 24.3 cu.in. or 364 cc / 22.2 cu.in.

  • Feed roller diameter, V-Steel 344 mm
  • Feed roller diameter, V-Steel Aggressive 344 mm
  • Calculated feed force (1) 398cc/364cc 18,4 kN / 16,8kN
  • Calculated feed speed (2) 4,2 m/sec / 4,6 m/sec
  • Maximum roller opening 394 mm
  • Minimum roller opening 12mm

1) calculated at 250 bar pressure

2) calculated at 210 l/min flow

 

DELIMBING

Four movable knives with patented positioning to minimize friction losses, which increases the active pulling force.

 

  • Max delimbing knife opening 408 mm
  • Max full coverage delimbimg diameter (1) 300 mm

1) Note includes bottom knife

 

HYDRAULICS

  • Maximum pressure 250 bar
  • Maximum flow 210 l/min

Min. requirements for acceptable performance :

  • Flow 150 l/min

CONTROL SYSTEM

Log Mate 500 with diameter and length measuring: Full system diagnosis, value bucking, StanForD 2010, multi-stemming report, powerful production reporting…

 

Interfaces Log Max heads can be seamlessly installed on any machine running an other control system. These powerful and easy to implement interfaces are available for all major manufacturers. (John Deere, Rottne, Ponsse…)
Read more »

 

ROTATOR

  • Indexator AV4EI with 360˚ rotation
  • Indexator AV12S with 360˚ rotation +24kg
  • Indexator H132 with 360˚ rotation +31kg

FEED ROLLERS

v-steel rollers  

V-Steel

By placing the stud bars in angled rows, Log Max has obtained a self cleaning feed roller with very high pulling force both in forward and reverse, without risk of spinning.

v-steel aggr. rollers  

V-Steel Aggressive

The V-steel Aggressive roller has studs that sink deeper in the tree trunk.

OPTIONAL CHAINSAW

truecut

An impressive new saw unit – the Log Max True-Cut

 

The Log Max 3000T feature the first generation 318 True-Cut and 218 True-Cut, both saws have a 19cc motor, the 318 has automatic chain tensioning the 218 has manual tensioning.

The key component of the True-Cut system is the intelligent saw motor with integrated valving solutions for saw motor speed and saw bar control. By continuously sensing the motor speed and adjusting the saw bar feed rate accordingly, the True-Cut maintains an almost constant chain speed of 40 m/s throughout the cutting cycle. This yields an impressive cutting performance – the True-Cut is up to 35 % faster than conventional saw units! By locating the valve for motor speed control inside the motor it is able to react instantly to changes in motor speed and practically eliminate any over-revving that is seen in a convention- al saw unit. Not only does this reduce the stress on the motor but it also provides a safer work environment by reducing the risk of chain shots.
The True-Cut saw units also features a longer stroke cylinder and a higher resolution cutting con- trol sensor. These additions provide for a more precise control of the saw bar resulting in maxi- mized cutting performance and color marking precision. The True-Cut is optimized at the factory and should not need any further setting changes in the field.

MULTI-STEMMING

Accumulation kit

 

This allows the head to be used as a combination head – both as a conventional harvester as well as a multi-stemming head for thinning small wood or in late brush cuttings.

 

The Log Max Accumulation Kit can be run with Log Mate 500, 402, Motomit, CabsWin, Dasa 380, Ponsse Opti, Timbermatic and Komatsu Maxi.

multi-stemming

FLOATING TOP KNIFE

Active Friction Control

 

The new generation floating top knife featuring Active Friction Control actively controls and adjusts the amount of friction between the log and the harvesting head’s frame. There is no need to go out and change the settings by adjusting the unit, everything is now set automatically. Low friction is desired as it leads to lower fuel consumption and heat generation. There is the exception of when delimbing heavily branched trees with small diameter limbs a higher friction minimizes the risk of simply bending them flat.

The harvester’s computer is the brain of the Active Friction Control and based on your settings, the Log Max head behaves optimally depending on tree species and diameter. For example, a thinning of pine and birch can behave quite differently based on tree species.

active friction control

EXTRA EQUIPMENTS

  • Field repair kit
  • Stump treatment
  • Color Marking
  • Snow cover
  • Fixed protection plate
  • Rotator control
  • Rod cover
  • Find end sensor

Volver al catálogo Log Max

Regresar al catálogo de esta marca

Catálogo General

Todos los productos

Contacte con nosotros

Área de contacto

Este sitio web utiliza cookies para que usted tenga la mejor experiencia de usuario. Si continúa navegando está dando su consentimiento para la aceptación de las mencionadas cookies y la aceptación de nuestra política de cookies, pinche el enlace para mayor información.

ACEPTAR
Aviso de cookies